Save/Restore Viewport rotates one time after saving

[deHarro]

Hi Martin,
just encountered another neat feature of OCP :)

Set the viewport orientation to your liking.
-> Move Viewport somewhat by Middle Mouse Key (Wheel)
Save this setting.
Restore this setting -> Viewport rotates by 180°
...
Mhmm, occured three times in series.
Now, just to be sure I didn't forget a step, I tested again and there is no problem.
Always restores as saved before... 8-(

Ok, then.. Happy Easter!
...
Tried some more options and heureka!
See list of operations above.
The move operation seems to have some cm displacement to get the effect I described.

Harald

[martin2250]

Hi Harald,

it may be a bit late, but happy Easter to you too!

I just tried to reproduce this behavior and it occurred first try... then I went into Visual Studio to debug it, re-built the project and now I can't reproduce it anymore? I'll leave this issue open and I'd suggest you to try to reproduce it when the next version is released. Very strange indeed.

Thanks!
Martin

[deHarro]

Ok, I'll test it with the new release.
It's not there already, isn't it?
Harald

[martin2250]

Nope, still waiting for a few more changes to "accumulate".

[deHarro]

Ok, kein Ding :-) Gruß Harald

…

_______________________ Modellbau&Elektronik <http://www.harald-sattler.de/> www.harald-sattler.de Von: Martin Pittermann [mailto:notifications@github.com] Gesendet: Samstag, 25. April 2020 09:25 An: martin2250/OpenCNCPilot <OpenCNCPilot@noreply.github.com> Cc: deHarro <harry0001@satharo.de>; Author <author@noreply.github.com> Betreff: Re: [martin2250/OpenCNCPilot] Save/Restore Viewport rotates one time after saving (#132) Nope, still waiting for a few more changes to "accumulate". — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#132 (comment)> , or unsubscribe <https://github.com/notifications/unsubscribe-auth/AGIUQJUO3HASVKWAHXRQAV3ROKF4JANCNFSM4MFN5EUA> .

[martin2250]

so, jetzt aber :) Konnte das Verhalten auch im neuen build nicht reproduzieren.

Grüße
Martin

[deHarro]

Hi Martin,
I'm so sorry to tell you... it still occurs.

I'm not able to get the initial sequence to make it happen, but if I got the 180° flipping, it occurs again and again.

Perhaps it has to do with a "Reset 3D Viewport" operation I issued during my tests.

First I did the following:
Start OCP 1.5.9.0 for the first time after copying all files to the old location.
Open a design
Rotate the design by RM to be roughly aligned horizontally
Save Viewport Orientation
Restore Viewport
Nothing special, all as expected.

But then I issued a "Restore 3D Viewport" inbetween:
Start OCP
Open a design
Restore 3D Viewport
Rotate the design by RM to be roughly aligned horizontally
Save Viewport Orientation
Restore Viewport
-> here the design rotates by 180°

When I then rotate the design to any orientation (to realize whether it rotates again or not) and save and restore, it is rotated by 180° every time from then on.

Harald

[martin2250]

Hi again, I'll give it another go when I have some spare time. For now I think we can still live with this bug :)

Cheers,
Martin

[deHarro]

Fine, no hurry! :-)

[deHarro]

Perhaps it's fixed with my last update to "Lay flat..." (as of 08.09.0224)