Skip to content

malejo97/demo_rvsummit_23

Repository files navigation

demo_rvsummit_23

RISC-V IOMMU Demo for the RISC-V Summit 2023

Table of Contents


License

This work is licensed under the Apache-2.0 License. See the LICENSE file for details.

About this Repository

Demo Capture

RISC-V IOMMU Demo for the RISC-V Summit 2023, presented in the Technology Innovation Institute (TII) booth.

It consists of a game similar to the russian roulette, in which a DMA device is programmed to write zeros into critical memory regions of a single-core CVA6-based platform executing Bao hypervisor and one baremetal guest atop of it. The demo is carried out in a Genesys2 FPGA board. The user navigates through the demo using the five push buttons in the board.

An Input/Output Memory Management Unit (IOMMU) is integrated into the platform. It is enabled by default, but can be disabled using one of the eight switches in the board. However, the lethal switch is selected randomly on every attack. The user can iterate eight times trying switches individually to find the lethal one, or enable multiple switches in a single attack.

The user can select between two targets: OpenSBI and Bao hypervisor. The lethal attack will take down the system in both options.

Dependencies

Functional code

To compile Bao hypervisor with the baremetal guest and OpenSBI, you need the riscv64-unknown-elf- and riscv64-unknown-linux-gnu- toolchains installed and added to your $PATH.

You can download them from the following links:

GUI

In order to run the Graphical User Interface of the demo, you need to install the following python packages:

  • PyQt5 v5.15.9
  • pyserial v3.5

To install these packages:

python3 -m pip install PyQt5
python3 -m pip install pyserial

You may have issues trying to install these packages due to the version of pip. If it is the case, update pip before installing the packages:

pip install --upgrade pip 

Usage

Generating the binary file

To compile Bao with the baremetal guest and OpenSBI, ensure you have initialized all required submodules. In the top directory of the repo, run:

git submodule update --init --recursive bao-hypervisor opensbi

Then, to compile all sources, run in the top directory of the repository:

./build_all

All output files will be in the output directory.

Copying to the SD Card

To copy the binary file to the SD card:

  1. Carefully, identify the dev file associated to your SD Card (e.g., /dev/sda, /dev/mmcblk).
sudo fdisk -l
  1. Format the SD card. Replace <dev_file> with the dev file you identfied in step 1.
sudo sgdisk --clear --new=1:2048:7000 --new=2 --typecode=1:3000 --typecode=2:8300 <dev_file> -g

ℹ️ To speed up the loading of the image, the BOOT (first) partition of the SD card is formatted to just the right size to store the binary file (~2.42 MiB).

  1. Copy the binary file to the SD card. Again, replace <dev_file> with the dev file you identfied in step 1.
sudo dd if=output/fw_payload.bin of=<dev_file> oflag=sync bs=1M

Configuring the Genesys2 board

Insert the SD Card with the binary file into the Genesys2 board.

The bitstream required for the demo is already stored in the flash memory of the board. Thus, after turning on the board, wait for the DONE led to be ON, and press the PROG push button to load the bitstream.

Wait for the DONE led to be ON again, and then press the RESET push button. The board will start loading the image from the SD card. This takes approximately 20 seconds.

ℹ️ If for some reason you need to program the FPGA through the JTAG interface using Vivado, the bitstream is located in fpga/ariane_xilinx.bit.

ℹ️ This demo ends with the crashing of the system. After configuring the FPGA board, you only need to press the RESET button to restart.

Running the GUI

Before running the GUI application, you need to give full permissions to the serial port dev file.

sudo chmod 777 <serial_port>

Where <serial_port> is the label of the serial port connected to the FPGA board (e.g., /dev/ttyUSB0).

Then, to execute the GUI application, run

python3 gui/main.py <serial_port>

About

RISC-V IOMMU Demo for the RISC-V Summit 2023

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages