This file should give you some help on how to install this driver.

OFFICIALLY SUPPORTED OPERATING SYSTEMS

• FreeBSD-8-stable
• FreeBSD-9-stable
• FreeBSD-10-stable
• FreeBSD-11-stable
• FreeBSD-12-stable
• FreeBSD-13-stable

FEATURES

• support for 512-tap FFT Echo Cancelling
• support for EuroISDN, DSS1 (point to point and point to multipoint)
• support for overlap sending and dial in digits
• support for hold and retrieve in NT-mode
• support for early B-channel connection when dialing out
• support for Basic Rate Interface, 2xB, in software and hardware
• support for Primary Rate Interface, 30xB, in software and hardware
• driver uses a per controller mutex to protect data and chip access
• direct access to D-channel and B-channels through /dev/ihfcX.Y
• full support for NT-mode in software and hardware **
• new "CAPI 2.0" application interface
• new "DSS1" protocol
• new "isdntrace"
• new "isdndecode"
• new "isdnd"
• new "capiserver"

** not all hardware can run NT-mode

SUPPORTED HARDWARE

See "man ihfc" after install.

Basic chips supported:

IPAC / ISAC / HSCX / HFC / WINBOND

• HFC - based devices (all works, recommended)
  • AcerISDN P10
  • Asuscom ISDNLink P-IN100-ST-D2
  • Bewan ISDN USB TA
  • Bewan Modem RNIS USB
  • Billion ISDN tiny USB modem
  • Billion USB TA 2
  • DrayTec ISDN USB
  • DrayTek USB ISDN TA (MiniVigor)
  • HFC-2BDS0 ISA/PnP/PCI/USB ISDN
  • HFC-E1 PCI ISDN
  • HFC-4S PCI ISDN
  • HFC-8S PCI ISDN
  • Motorola MC145575
  • OliTec ISDN USB
  • OliTec Modem RNIS USB V2
  • Stollmann USB TA
  • Teles S0/16.3c PnP
  • Telewell
  • Trust ISDN
  • Twister ISDN TA
  • Xplorer 500
  • Zoltrix Speedier 128K PCI
• ISAC - based devices (all should work, not recommended)
  • Asuscom ISDNlink 128K ISA
  • AVM A1
  • AVM Fritz!Card
  • AVM Fritz!Card PnP
  • AVM Fritz!Card PCI
  • AVM Fritz!Card PCI version 2 (** NOTE)
  • Compaq Microcom 610 (Compaq series PSB2222I)
  • Creatix ISDN-S0 P&P
  • Creatix S0/16 PnP
  • Dr.Neuhaus Niccy Go@
  • Dynalink IS64PH
  • ELSA MicroLink ISDN/PCI
  • ELSA QuickStep 1000pro ISA
  • ELSA QuickStep 1000pro PCI
  • Eicon.Diehl DIVA 2.0 ISA PnP
  • Eicon.Diehl DIVA 2.02 ISA PnP
  • ITK ix1 Micro V3.0
  • MultiTech MT128SA
  • Sedlbauer Win Speed
  • Siemens I-Surf 2.0 PnP
  • Teles S0/16.3 PnP
• Winbond (all works, not recommended)
  • Asuscom ISDNLink P-IN100-ST-D
  • Asuscom ISDNLink TA-280-ST-W (USB)
  • Dynalink IS64PPH
  • Planet PCI ISDN Adapter (IA128P-STDV)
• Tiger300/320 - based devices (all works, not recommended)
  • NETjet-S PCI ISDN
  • Teles PCI-TJ

** NOTE: Some versions of the "AVM Fritz!Card PCI version 2" card do not work in voice mode!

HOW TO INSTALL AS ROOT

#
# Ensure that libcapi is installed
#

make configure HAVE_ALL=YES KMODDIR=/boot/modules \
    LIBDIR=/usr/local/lib BINDIR=/usr/local/bin \
    INCLUDEDIR=/usr/local/include \
    MANDIR=/usr/local/man/man

make -m /usr/src/share/mk SYSDIR=/usr/src/sys depend all HAVE_ALL=YES
make -m /usr/src/share/mk SYSDIR=/usr/src/sys install HAVE_ALL=YES

HOW TO SET NT-MODE

See "man isdnconfig"

#
# USB controllers start at n = 63 and decrements
#
# NOTE: NT-mode will only be set when "isdnconfig" is executed.
# When one plugs an USB ISDN adapter, TE-mode will be selected by
# default. This might change in the future.
#

USING WITH ASTERISK, http://www.asterisk.org

On FreeBSD asterisk can be installed from "/usr/ports/net/asterisk". After that one has to install the ISDN4BSD module. Then get chan_capi [1], install it by running "gmake all" and then "gmake install", and create a "capi.conf" file like the one in the "examples" directory. Then put something sensible in your "extensions.conf" and it should work.

NOTES

If more than 8 units needs to be supported please edit "src/sys/i4b/include/i4b_global.h"

ISDN4BSD FORUM

freebsd-isdn@freebsd.org

--HPS