Skip to content

cpetrich/Smart-Tech-Sound-BLE

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

6 Commits
 
 
 
 

Repository files navigation

Bluetooth Low Energy (BLE) Communication with BRIO Smart Tech Sound train

Notes on BLE communication with BRIO Smart Tech Sound train
Author: Chris Petrich, 25 Dec 2023.
License: CC-BY, https://creativecommons.org/licenses/by/4.0/
This repository is not affiliated with BRIO.

About

This document is about BRIO Smart Tech Sound as sold around 2023. The trains can be controlled

  • via Bluetooth Low Energy (BLE) with the BRIO Smart Tech Sound App,
  • 13.56 MHz RFID Action Tunnels such as those found in sets 33974 and 33972, or
  • three buttons on the train (forward, stop, reverse).

Results

A valid control event results in a sequence of one to ca. five BLE notifications in conjunction with a sequence of sound, light, and motion effects. These sequences are part of the firmware of the train, which can be updated with the app.

The trains are BLE peripherals (i.e. servers) that advertise themselves as Smart 2.0. The service UUID is b11b0001-bf9b-4a20-ba07-9218fec577d7, and within this, the characteristic for commands to the train is b11b0002-bf9b-4a20-ba07-9218fec577d7, while the characteristic for notifications from the train back to the BLE client is b11b0003-bf9b-4a20-ba07-9218fec577d7.

BLE commands and notifications are a string of unsigned 8-bit integers framed by start byte 0xAA and single-byte checksum, <C>, at the end. The checksum is calculated from the sum of the bytes of the command or notification (i.e. without the start byte 0xAA) as follows:

<C> = (0x100 - (Sum & 0xFF)) & 0xFF

Unknown commands or commands with checksum errors are silently ignored (i.e. no notifications are sent).

Among the list of recognized commands are

Command Meaning
02:01:<speed> Set speed of train and play appropriate light and sound effects.
03:56:AA:<effect> Stop train, set sound effect theme, and play sound.
03:52:<b1>:<b2> App sends 5 startup messages with <b1>=M,T,Q,W,X, respectively, and <b2>=0x00.
06:06:00:00:<MSB>:<LSB> Start binary data transfer for firmware update.
1x:50:<id>:<seq>:<type>:<payload> x={0,6,c}, <payload>=18 or 24 bytes. Firmware parameters of preceeding binary transfer.
02:0a:0f End of firmware update.

Commands are sent as Write Requests (CYBLE_EVT_GATTS_WRITE_REQ), except the 1x:50:... commands and binary data, which are Write Commands (CYBLE_EVT_GATTS_WRITE_CMD_REQ). The train will send a notification in return to each command (i.e. not for binary data).

Train speed, <speed>, is coded as

  • 0x00 for "off",
  • values 0x01 to 0x08 for forward, and
  • values 0x11 to 0x18 for backward.

Currently, power with values 0x01and 0x11 is too low to actually move the train.

The sound effect themes are coded depending on context:

Effect <effect> <eff1> <eff2> <eff3> <eff4>
Honk 0xf0 0x15 0x1d 0x11 0x19
Whistle 0xf1 0x16 0x1e 0x12 0x1a
Horn 0xf2 0x17 0x1f 0x13 0x1b
Spaceship 0xf3 0x18 0x20 0x14 0x1c

Custom sound recordings are coded as, for example, 0x81 or 0x82 in <eff1>.

The first notification message after pressing a button on the train is:

Button First Notification
Stop 02:80:01
Forward 02:80:02
Backward 02:80:03

The first notification when passing through an Action Tunnel is:

Action Tunnel First Notification
"Stop" from forward 08:81:02:00:00:<eff1>:91:3a:03
"Stop" from backward 08:81:02:00:00:ef:0f:00:0f
"Change direction" 08:81:03:00:00:ef:0f:00:0f
"Break" down from forward 08:81:07:40:00:<eff2>:6f:31:20
"Break" down from backward 08:81:07:40:00:<eff2>:6f:31:30
"Fix" without repair 08:81:0c:00:00:<eff3>:f9:9a:<speed>
"Fix" with repair, forward 08:81:0c:00:00:ef:0f:00:03
"Fix" with repair, backward 08:81:0c:00:00:ef:0f:00:0f
double tunnel, top 08:81:25:00:00:ef:df:aa:<speed>
"Sound" (orange) 08:81:39:00:00:87:01:3a:<speed>
"Train Service Station", switch, forward 08:81:4d:00:00:ef:df:aa:03
"Train Service Station", switch, backward 08:81:4d:00:00:ef:3f:3a:13
"Train Service Station", washing, forward 08:81:4e:00:00:ef:df:aa:03
"Train Service Station", washing, backward 08:81:4e:00:00:ef:0f:00:0f
"Train Service Station", repair, forward 08:81:4f:00:00:ef:df:aa:03
"Train Service Station", repair, backward 08:81:4f:00:00:ef:0f:00:0f
"Rescue", forward 08:81:54:00:00:ef:df:aa:03
"Rescue", backward 08:81:54:00:00:ef:00:00:03

The fith byte (0x00 in all examples above) is a sequence number whenever multiple notifications are emitted. The train action, number of notifications, and the values from the sixth byte onward depend on the firmware version.

Action tunnel notifications are sent only if the train is in motion.

Apparently, notifications get sent after the actual action has already been initiated by the train, i.e. it does not seem to be possible to cleanly override the pre-programmed behavior by sending BLE commands (there may be train jerking and aborted sounds). Sending a command in response to a notification from an Action Tunnel may cause the train to detect the Action Tunnel again, leading to a loop that lasts until the train is out of range of the tunnel.

Examples

BLE Commands

Byte String Meaning
aa:02:01:08:f5 Full speed forward
aa:02:01:02:fb Slowly forward
aa:02:01:00:fd Stop the train
aa:02:01:18:e5 Full speed backward
aa:03:56:aa:f0:0d Set sound theme to "honk" (default)
aa:03:56:aa:f1:0c Set sound theme to "whistle"

In JavaScript, commands could be sent to the BLE peripheral like so: characteristic.writeValue( new Uint8Array([0xaa,0x02,0x01,0x08,0xf5]) ).

It follows a minimal code example to make the train move forward using the Web Bluetooth API. Read the Disclaimer at the end of this page before proceeding. Copy text to a file with extension .html and open in Chrome or Edge. Turn on the BRIO Smart Tech Sound train, enable BLE on the computer and click the button on the web page to initiate the pairing process. Note that this will work only on Chrome and Edge.

<!DOCTYPE html>
<html>
<head>
<title>BLE test</title>
<meta name="author" content="Chris Petrich" />
</head>
<body>
<h1>BRIO Smart Tech Sound example for Chrome and Edge</h1>
<button onclick="connectBLE()">Click to Connect to Train and Start Driving</button>
<script>
const serviceUUID = "b11b0001-bf9b-4a20-ba07-9218fec577d7";
const commandCharacteristicUUID = "b11b0002-bf9b-4a20-ba07-9218fec577d7";
function connectBLE() {
  navigator.bluetooth.requestDevice(
    { filters: [{ services: [serviceUUID] }] })
    .then(device => device.gatt.connect())
    .then(server => server.getPrimaryService(serviceUUID))
    .then(service => service.getCharacteristic(commandCharacteristicUUID))
    .then(characteristic => characteristic.writeValue( new Uint8Array([0xaa,0x02,0x01,0x08,0xf5]) ));
}
</script>
</body>
</html>

BLE Notifications

Example notification sequence of a train going backward through the "fix" tunnel while still being damaged from the "broken" tunnel. Initial speed 0x18, and sound effect 0xf0 (default).

aa:08:81:0c:00:00:ef:0f:00:0f:5e
aa:08:81:0c:00:01:ef:0f:00:03:69
aa:08:81:0c:00:02:21:c1:91:0f:e7
aa:08:81:0c:00:03:00:3f:3a:18:d7
aa:08:81:00:00:00:00:3f:3a:18:e6

Disclaimer

I am not affiliated with BRIO. This is not an official documentation by BRIO. Information on this page are the result of some basic reverse engineering effort on my part, and results may contain errors. Information may be out of date as implementation and firmware of the trains could change at any time. Note that your train may get permanently unresponsive if you inadvertently initiate a firmware update. Use information in this repository at your own risk.

Sources

About

BLE commands to control BRIO Smart Tech Sound trains.

Topics

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages