From 506e4fa99b9e9fb23eebcf75791f6c8610013b64 Mon Sep 17 00:00:00 2001 From: shiftingtech <53156353+shiftingtech@users.noreply.github.com> Date: Sun, 14 Jul 2024 16:50:13 -0600 Subject: [PATCH] Config cleanups (#479) * config cleanups * Update Voron2_M8P-v2.0_config.cfg * Update Voron2_M8P-v1.1_config.cfg * Update Voron2_M8P-v1.0_config.cfg * Update Voron2_Kraken_Config.cfg * Update Voron2_Octopus_Config.cfg * Update Voron2_SKR_13_Config.cfg * Update Voron2_SKR_14_Config.cfg * Update Voron2_Spider_Config.cfg * Update Voron2_Kraken_Config.cfg * Update Voron2_M8P-v1.0_config.cfg * Update Voron2_M8P-v1.1_config.cfg * Update Voron2_M8P-v2.0_config.cfg * Update Voron2_Octopus_Config.cfg * Update Voron2_SKR_13_Config.cfg * Update Voron2_SKR_14_Config.cfg * Update Voron2_Spider_Config.cfg --- .../klipper_configurations/Kraken/Voron2_Kraken_Config.cfg | 4 ++-- .../klipper_configurations/M8P/Voron2_M8P-v1.0_config.cfg | 2 +- .../klipper_configurations/M8P/Voron2_M8P-v1.1_config.cfg | 6 +++--- .../klipper_configurations/M8P/Voron2_M8P-v2.0_config.cfg | 6 +++--- .../Octopus/Voron2_Octopus_Config.cfg | 4 ++-- .../klipper_configurations/SKR_1.3/Voron2_SKR_13_Config.cfg | 6 +++--- .../klipper_configurations/SKR_1.4/Voron2_SKR_14_Config.cfg | 6 +++--- .../klipper_configurations/Spider/Voron2_Spider_Config.cfg | 4 ++-- 8 files changed, 19 insertions(+), 19 deletions(-) diff --git a/firmware/klipper_configurations/Kraken/Voron2_Kraken_Config.cfg b/firmware/klipper_configurations/Kraken/Voron2_Kraken_Config.cfg index 57c92c85..ded51229 100644 --- a/firmware/klipper_configurations/Kraken/Voron2_Kraken_Config.cfg +++ b/firmware/klipper_configurations/Kraken/Voron2_Kraken_Config.cfg @@ -24,7 +24,7 @@ ## Fine tune E steps [extruder] section [mcu] -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/{REPLACE WITH YOUR SERIAL} restart_method: command @@ -601,4 +601,4 @@ gcode: # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. - RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 \ No newline at end of file + RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 diff --git a/firmware/klipper_configurations/M8P/Voron2_M8P-v1.0_config.cfg b/firmware/klipper_configurations/M8P/Voron2_M8P-v1.0_config.cfg index 0cb31a21..994f1903 100644 --- a/firmware/klipper_configurations/M8P/Voron2_M8P-v1.0_config.cfg +++ b/firmware/klipper_configurations/M8P/Voron2_M8P-v1.0_config.cfg @@ -10,7 +10,7 @@ ## [X in MOTOR1] - B Motor ## [Y in MOTOR2] - A Motor ## [E in MOTOR8] - Extruder -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/YOU_DIDNT_CHANGE_ME_YET #restart_method: command diff --git a/firmware/klipper_configurations/M8P/Voron2_M8P-v1.1_config.cfg b/firmware/klipper_configurations/M8P/Voron2_M8P-v1.1_config.cfg index baf34513..99bbcaf5 100644 --- a/firmware/klipper_configurations/M8P/Voron2_M8P-v1.1_config.cfg +++ b/firmware/klipper_configurations/M8P/Voron2_M8P-v1.1_config.cfg @@ -1,8 +1,8 @@ -# This file contains common pin mappings for the BIGTREETECH Manta M8P V1.0 +# This file contains common pin mappings for the BIGTREETECH Manta M8P V1.1 # To use this config, the firmware should be compiled for the # STM32G0B1 with a "8KiB bootloader" and USB communication. -# This config is currently only correct for V1.0 boards +# This config is currently only correct for V1.1 boards # # See docs/Config_Reference.md for a description of parameters. @@ -10,7 +10,7 @@ ## [X in MOTOR1] - B Motor ## [Y in MOTOR2] - A Motor ## [E in MOTOR8] - Extruder -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/YOU_DIDNT_CHANGE_ME_YET #restart_method: command diff --git a/firmware/klipper_configurations/M8P/Voron2_M8P-v2.0_config.cfg b/firmware/klipper_configurations/M8P/Voron2_M8P-v2.0_config.cfg index 4a54f3a0..dd30df5c 100644 --- a/firmware/klipper_configurations/M8P/Voron2_M8P-v2.0_config.cfg +++ b/firmware/klipper_configurations/M8P/Voron2_M8P-v2.0_config.cfg @@ -1,8 +1,8 @@ -# This file contains common pin mappings for the BIGTREETECH Manta M8P V1.0 +# This file contains common pin mappings for the BIGTREETECH Manta M8P V2.0 # To use this config, the firmware should be compiled for the # STM32G0B1 with a "8KiB bootloader" and USB communication. -# This config is currently only correct for V1.0 boards +# This config is currently only correct for V2.0 boards # # See docs/Config_Reference.md for a description of parameters. @@ -10,7 +10,7 @@ ## [X in MOTOR1] - B Motor ## [Y in MOTOR2] - A Motor ## [E in MOTOR8] - Extruder -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/YOU_DIDNT_CHANGE_ME_YET #restart_method: command diff --git a/firmware/klipper_configurations/Octopus/Voron2_Octopus_Config.cfg b/firmware/klipper_configurations/Octopus/Voron2_Octopus_Config.cfg index 071a60dc..cb21a876 100644 --- a/firmware/klipper_configurations/Octopus/Voron2_Octopus_Config.cfg +++ b/firmware/klipper_configurations/Octopus/Voron2_Octopus_Config.cfg @@ -24,7 +24,7 @@ ## Fine tune E steps [extruder] section [mcu] -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/{REPLACE WITH YOUR SERIAL} restart_method: command @@ -590,4 +590,4 @@ gcode: # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. - RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 \ No newline at end of file + RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 diff --git a/firmware/klipper_configurations/SKR_1.3/Voron2_SKR_13_Config.cfg b/firmware/klipper_configurations/SKR_1.3/Voron2_SKR_13_Config.cfg index a42582e3..c4f55212 100644 --- a/firmware/klipper_configurations/SKR_1.3/Voron2_SKR_13_Config.cfg +++ b/firmware/klipper_configurations/SKR_1.3/Voron2_SKR_13_Config.cfg @@ -63,7 +63,7 @@ ## [Y in Y] - A Motor ## [E in E0] - Extruder [mcu] -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_lpc1768_00000-if00 ##-------------------------------------------------------------------- @@ -74,7 +74,7 @@ serial: /dev/serial/by-id/usb-Klipper_lpc1768_00000-if00 ## [Z2 in Z] - Rear Right ## [Z3 in E0]- Front Right [mcu z] -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_lpc1768_00000-if00 ##-------------------------------------------------------------------- @@ -582,4 +582,4 @@ gcode: # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. - RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 \ No newline at end of file + RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 diff --git a/firmware/klipper_configurations/SKR_1.4/Voron2_SKR_14_Config.cfg b/firmware/klipper_configurations/SKR_1.4/Voron2_SKR_14_Config.cfg index dff0252c..41b059e0 100644 --- a/firmware/klipper_configurations/SKR_1.4/Voron2_SKR_14_Config.cfg +++ b/firmware/klipper_configurations/SKR_1.4/Voron2_SKR_14_Config.cfg @@ -64,7 +64,7 @@ ## [Y in Y] - A Motor ## [E in E0] - Extruder [mcu] -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_lpc1768_00000-if00 ##-------------------------------------------------------------------- @@ -75,7 +75,7 @@ serial: /dev/serial/by-id/usb-Klipper_lpc1768_00000-if00 ## [Z2 in Z] - Rear Right ## [Z3 in E0]- Front Right [mcu z] -## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_lpc1768_00000-if00 ##-------------------------------------------------------------------- @@ -582,4 +582,4 @@ gcode: # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. - RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 \ No newline at end of file + RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 diff --git a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg index f7a85fd5..70398bd1 100644 --- a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg +++ b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg @@ -14,7 +14,7 @@ ## Fine tune E steps [extruder] section [mcu] -## Obtain definition by "ls -l /dev/serial/by-id/" +## Obtain definition by "ls /dev/serial/by-id/*" ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_000000000000000000000000-if00 @@ -525,4 +525,4 @@ gcode: # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. - RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 \ No newline at end of file + RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0